Sosialisasi Pengolahan Sampah dengan Penggunaan Alat Pemotong Ring AMDK Gelas Plastik yang Aman di Bank Sampah SiHatin
DOI:
https://doi.org/10.62951/unggulan.v2i1.1195Keywords:
Plastic Cup, Ring Cutter, Waste BankAbstract
The increase in consumption of plastic bottled drinking water (AMDK) has led to an increase in the amount of plastic waste that requires special handling. One of the main challenges in managing this waste is the process of cutting plastic cup rings, which has been done manually using a cutter or small knife. This manual method is not only less effective but also increases the risk of injury for waste pickers. This research aims to develop a safer and more effective plastic cup ring cutter. Through a socialisation programme and implementation of the tool at Bank Sampah SiHatin, the effectiveness of the tool was tested by comparing the manual method and the use of the cutting tool. The results of the analysis show that the use of this tool is able to increase the cutting speed by 58%, produce more uniform cuts, and eliminate the risk of injury due to the use of cutters. In addition, this tool also improves occupational safety and health (K3) aspects and has a positive impact on the economic value of cutting products. Thus, this innovation is an effective solution in plastic waste management in the informal sector and can be adopted more widely in various other Waste Banks
References
Maryani, A., Ratnasanti, D. A., & Partiwi, S. G. (2019). Perbaikan perancangan alat pengupas mete menggunakan metode value engineering. Tekmapro: Journal of Industrial Engineering and Management, 14(2), 82–91. https://doi.org/10.33005/tekmapro.v14i2.50
Muhfidin, R., Sari, S. N., & Prastowo, R. (2024). Analisis kapasitas mesin pencacah limbah plastik dan tekstil menggunakan unit penghancur (shredder). G-Tech: Jurnal Teknologi Terapan, 8(3), 1474–1483. https://doi.org/10.33379/gtech.v8i3.4400
Oktaviani, S., & Mauluddin, Y. (2021). Perancangan alat bantu pemotong kerupuk untuk meningkatkan kapasitas produksi UMKM Samawi. Jurnal Kalibrasi, 19(1), 99–109. https://jurnal.itg.ac.id/
Sebayang, D. F., Surbakti, L. S., Hasballah, T., & Pardede, S. (2023). Rancang bangun mesin pemotong ring cup minuman sistem rotari kapasitas 5 kg per jam. Jurnal Teknologi Mesin UDA, 4(1), 214–224.
Setyawati, E. Y., & Priyo Siswanto, R. S. H. (2020). Partisipasi perempuan dalam pengelolaan sampah yang bernilai ekonomi dan berbasis kearifan lokal. Jambura Geo Education Journal, 1(2), 55–65. https://doi.org/10.34312/jgej.v1i2.6899
Simanjuntak, D. N. R., Manik, Y., & Siboro, B. A. H. (2021). Perancangan rak sepatu untuk laboratorium desain produk dan inovasi Institut Teknologi Del dengan metode value engineering dan quality function deployment (QFD). Jurnal Ilmiah Teknologi dan Rekayasa, 26(2), 122–138. https://doi.org/10.35760/tr.2021.v26i2.4469
Soewono, A. D., Liutomo, J., & Darmawan, M. (2021). Rancang bangun plastic waste shredder untuk mengolah sisa limbah plastik proses injection mould. Jurnal Rekayasa Mesin, 16(1), 1–8. https://jurnal.polines.ac.id/index.php/rekayasa
Syaiful Fadly, M., Asmara, A., Rismanto, M., & Fadholy, A. (2024). Pengolahan sampah plastik menggunakan alat pemotong ring cincin gelas plastik di Bank Sampah Navoe Kelurahan Taipa. Forpit: Jurnal Forum Pengabdian Ilmu Teknik, 1(1), 1–4.
Triadi, N. Y., Martana, B., & Pradana, S. (2020). Perancangan mesin pencacah plastik tipe shredder dan alat pemotong tipe reel. Jurnal Rekayasa Mesin, 15(2), 144–153. https://jurnal.polines.ac.id/index.php/rekayasa
Wibowo, E. A., Hidayah, M. N. W., Ma’arif, E. S., Sundari, S., & Ma’arif, I. S. (2024). Optimasi penentuan material alat pemotong ring gelas plastik AMDK: Sebuah analisis pendekatan analytical hierarchy process (AHP). Jurnal Serambi Engineering, IX(3), 9541–9549.
Wibowo, E. A., Hidayah, M. N. W., Munandar, G. M., Ardiansyah, R., & Rahmawati, N. F. (2025). Desain inovatif alat pemotong ring AMDK gelas plastik: Meningkatkan efisiensi dan keamanan proses daur ulang di sektor informal dengan pendekatan value engineering. JUTIN: Jurnal Teknik Industri Terintegrasi, 8(1), 1–7.
Wibowo, E. A., Munandar, G. M., & Hidayah, M. N. W. (2024). Formula optimal dalam penentuan aspek penting pada desain alat pemotong ring AMDK gelas plastik menggunakan metode quality function deployment (QFD). Industrika: Jurnal Ilmiah Teknik Industri, 8(1), 162–169. https://doi.org/10.37090/indstrk.v8i1.1354
Wibowo, E. A., Widyastuti, W., Betanursanti, I., Munandar, G. M., Rahmawati, N. F., & Ramadhani, W. A. (2024). Edukasi penggunaan alat pelindung diri (APD) pelindung jari pada pemilahan sampah AMDK gelas plastik di Bank Sampah SiHatin. Jurnal Pengabdian Masyarakat Indonesia, 3(1), 188–196. https://doi.org/10.55606/jpmi.v3i1.3442
Wibowo, E. A., Widyastuti, W., Betanursanti, I., Puspitasari, A. F., & Pamungkas, K. A. (2024). Evaluasi penggunaan alat pelindung diri (APD) dalam pemilahan sampah AMDK gelas plastik di Bank Sampah SiHatin. Jurnal Pengabdian Masyarakat Sains dan Teknologi, 3(2), 23–31. https://doi.org/10.58169/jpmsaintek.v3i2.464
Widyastuti, W., & Dicasani, A. (2023). Efektivitas metode identifikasi kata kansei: Review. Jurnal Inovasi Teknik Industri (JITIN), 2(2), 108–115. https://doi.org/jitin.v2iII.1289
Widyastuti, W., Wibowo, E. A., Dicasani, A., & Ernawati, E. (2025). Desain kansei wire stripper untuk pemilahan sampah kabel di sektor informal. Jurnal Teknik Industri Terintegrasi, 8(1), 585–591. https://doi.org/10.31004/jutin.v8i1.39943
Downloads
Published
How to Cite
Issue
Section
License
Copyright (c) 2025 Pelayanan Unggulan : Jurnal Pengabdian Masyarakat Terapan
This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.
